Reinitialize your Holosun EPS Carry Red Dot Sight

Occasionally, you may need to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the settings or are experiencing unexpected issues. Fortunately, resetting your Holosun is a easy process that can be completed in just a few steps.

Initially ensuring your red dot sight is turned on.
Locate the small reset button on the side of the device.
Utilize a paperclip to press and hold the reset switch for approximately 7 milliseconds.
Disengage the switch and your Holosun EPS Carry Red Dot sight will reboot.
Your red dot sight should now be set back to its factory settings.

Return to Your Holosun EPS Carry Red Dot to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to its factory configuration is a breeze. First, find the tiny button on the bottom of your optic. Then, press and hold it for around five seconds until you see the indicator light change. Your Holosun EPS Carry is now returned to its factory settings, ready for accurate shooting.

revive your Holosun EPS Carry Back to Action

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to detach the battery from your Holosun EPS Carry to prevent accidental activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these straightforward steps:

Hold down the power button for approximately 5 seconds.
A message will flash, indicating that the reset is successfuly initiated.
Release the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and verify your sight's functionality. If you encounter any further problems, don't hesitate to reach out to their technical assistance.

Restore Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

First, Turn on your Holosun EPS Carry by pressing the power button.
Next, press and hold both the mode button and the up/down adjustment button simultaneously.
While continue holding these buttons, press the power button once.
The display will show a confirmation prompt indicating that the reset process is initiated.
Allow the process to conclude. This may take a few moments. Once done, your Holosun EPS Carry will automatically deactivate.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Reinitialized to their default values.

Restore your Holosun EPS Carry through a Factory Original Settings

If your Holosun EPS Carry is acting up, a factory reset might be the fix. This will set back your sight to its How to factory reset holosun eps carry red dot initial settings, clearing any custom configurations you've made. To accomplish this reset, follow these straightforward steps:

Initially, find the reset switch on your EPS Carry.
Next, press a fine object, like a pen tip, to depress the reset lever.
As you keep the reset button pressed, power on your EPS Carry.
You'll blink a message showing that the reset is complete.

When the reset is finished, your EPS Carry will be set to its factory settings.